6
famiglie di protocolli industriali sullo stesso hardware
30 s
industrial protocol families on the same hardware
3
to select a new protocol combination
0
product families: gateways, power analyzers and I/O modules
01 programming software required and no changes to I/O tags or registers 02 Vantaggi Technology Protocolli Benefits Prodotti Protocols Procedura Products FAQ
01 Procedure
Con FLEX un unico dispositivo gestisce i protocolli delle reti seriali ed Ethernet industriali e semplifica la comunicazione tra PLC, dispositivi Master/Slave e Client/Server. Cambia il layout produttivo o il protocollo dell’impianto? Si riconfigura il dispositivo, non si sostituisce.
Senza FLEX
Without FLEX
02 Retrofitting
Technology Simpler ordering codes, quotations and purchase orders.
Lower storage and handling costs.
New protocols and product categories can be added over time.
Interoperability
On the field side, FLEX devices communicate via ModBUS RTU, ASCII and TCP-IP; on the PLC, SCADA or cloud side, you select the plant's protocol.
ModBUS ↔ OPC UA
ModBUS ↔ IEC 61850
ModBUS ↔ MQTT(s) o HTTP(s), verso cloud e broker
Il suffisso del codice prodotto indica la configurazione attiva. Con FLEX lo stesso dispositivo può passare da un suffisso all’altro.
-0 / baseModBUS
-PPROFINET IO
ModBUS ↔ MQTT(s) or HTTP(s), to cloud and brokersSupported protocols
The protocol is in the product codeOPC UA
The product code suffix identifies the active configuration. With FLEX, the same device can switch from one suffix to another.IEC 61850
-CMQTT cloud
Benefits FLEX is SENECA's proprietary multiprotocol technology: the same gateway, power analyzer or I/O module can switch from ModBUS to PROFINET, EtherNet/IP, OPC UA, IEC 61850 or MQTT without changing the hardware, wiring or ordering code.
I dispositivi compatibili si riconoscono dal distintivo FLEX nella scheda prodotto. La conversione richiede la revisione hardware indicata e il firmware più recente.
| Famiglia | Modelli di partenza | Protocolli disponibili | Revisione HW |
|---|---|---|---|
| Gateway Serie KEY Where to find FLEX technology |
Compatible devices feature the FLEX badge on their product pages. Conversion requires the specified hardware revision and the latest firmware. | Family | Base models Available protocols HW revision |
| KEY Series gateways protocol converters |
R-KEY-LT, Z-KEY-0, Z-KEY-2ETH and versions -P, -E, -U, -I, -C | ModBUS RTU / TCP-IP, PROFINET IO, EtherNet/IP, OPC UA, IEC 61850 | ≥ D |
| Moduli I/O Serie R I/O remoti |
R203 power analyzers | ModBUS RTU / TCP-IP, PROFINET IO, EtherNet/IP | R203-2-L (24 Vdc), R203-2-H (90..264 Vac) and versions -P, -E, -U, -I |
| Moduli I/O Serie ZE formato Z-PC 17,5 mm |
R Series I/O modules | ModBUS RTU / TCP-IP, PROFINET IO, EtherNet/IP | R203-2-L (24 Vdc), R203-2-H (90..264 Vac) and versions -P, -E, -U, -I |
remote I/O
Serie KEY: ModBUS, PROFINET, EtherNet/IP, OPC UA, IEC 61850 e MQTT.
Protocols Available combinations and minimum hardware revisions for each model are listed in the instruction manual. The MQTT code (-C) is available for KEY gateways.
KEY Series: ModBUS, PROFINET, EtherNet/IP, OPC UA, IEC 61850 and MQTT.
R203 Series for energy monitoring, compatible with any plant network.
I/O systems
Easy to configure
Connect the PC to the FLEX device via Ethernet.
2. Scan
3. Select

Select the new protocol combination in approximately 30 seconds.
Products FAQ
5. Restart
Alternatively, the firmware for the new configuration can be uploaded through the device's web server. After switching, update the PLC and network configuration for the new protocol. Before proceeding, check the latest firmware and instruction manual on the website.
A Z-KEY-0 used as a ModBUS gateway becomes a Z-KEY-P PROFINET IO gateway using the procedure above: same device, same connections, new protocol to the PLC.
Serve una revisione hardware minima, indicata in etichetta: ad esempio C per R-KEY-LT, F per Z-KEY, B per Z-KEY-2ETH e D per gli analizzatori R203. In caso di dubbio scrivi a SENECA indicando codice e numero di serie.
What is FLEX technology?
Do I need to change wiring, tags or registers?
No. Terminals, field wiring and the I/O point map remain unchanged, and no programming software is required. However, the PLC and network configuration must be adapted to the selected protocol.